1. Idling : Specially when the newest matrix is used intended for the initial time, it has to idle intended for about thirty moment, and for the summer time higher temperature season, it needs to water idle, the aim of idling is usually to more remove the soldadura effects to the matrix, and enhance the diamond saw blades to take care of the memory of inside quality below a high-speed rotation state.

2. Blocks shall not be significantly less than 0.five cubic meters, and area in a secure place, the underside ought to have the squared timbers, along with the blocks should be found during the symmetry in the worktable, which to produce sure which the balance in the worktable and blocks, without shaking and trembling.

3. Adjusting the travel switch according to the blocks dimension, to make the diamond saw blades raise and skip excursion within a reputable and valid scope. The saw blade edge must go away blocks greatest of 10-20mm just before sawing. Following sawing, the saw minimize should maintain about 20-40mm far away from your bottom of blocks, the saw blade ought to definitely exit blocks saw lower prior to the saw blade going across the turret, and the distance should not be significantly less than 150-200mm, this can be to help keep the blocks way in the saw blade striking.

4. The trial check isn't authorized before the saw idle stabling, and it isn't allowed to begin the saw blade in the event the blade edge is in speak to with blocks, not allowed to halt the blade rotation throughout the cutting. It ought to be stop to rotate after withdrawing through the blade cut.

5. It must immediately cease cutting when blocks shake, and it isn't allowed to still work right up until the blocks firmly mounted. In the course of the cutting processor, it isn't allowed to transfer blocks.

6. When the cutting blade clearly gradual straight down and even has folder knife phenomenon, it might be considered a belt slipping, loosening with the compressed nut or the penetration from the cutting depth is too big, the cutting pace is just too quick, it should be timely altered.

7. The line velocity should be adapted for the hardness and put on resistance of the produced stone , it is recommended to choose desk line pace cutting differing kinds of stone . Suggestion: The line pace is not large , a rise in cutting performance, will decrease the lifetime of the blade .

8. The feeding pace mostly depends on the performance with the processing material, in case the feeding velocity is simply too high, it will speed up the diamond dress in and tear or perhaps drop off, resulting in too much concrete core bits consumption; in case the feeding speed is just too slow, it is going to lead to the blade self-sharpening process can't be designed commonly, resulting cutting capability loss. Below common situation, the feeding pace should be sluggish when begun to cut, and also the speed should be uniform throughout cutting. Regarding the common typical components, the cutting depth should be 20mm.

9. The cutting depth regarding the medium-hardness stone these kinds of as marble, limestone, it could be penetrate regarding just one time, whilst with regard to the challenging and abrasive stone this sort of as granite, sandstone, it should be lower step by step. Utilizing the single blade saw to cut the granite stone, the penetration depth is often 10-20mm, along with the penetration depth intended for marble is 50-100mm, while if employing the multi-chip double-sided cutting the granite stone, every Penetration depth is 3-5mm.

10. In summary, the essential necessity intended for selecting the cutting method are: for the reduced hardness and good cutting overall performance stone, it might be lower slowly and deeply, otherwise, it should be minimize lightly and swiftly. In case the cutting speed in the cutting blade can't be keep since the very same parameter, it implies that the saw blade is blunt, it needs to reduce the cutting depth and improve the cutting velocity to sharp the saw blade.

Previous:How To Use Diamond Cutting Tools Safely Next:Transient Introduction on Diamond Blade Software Assortment

Thank you for your interest in the above content, please leave us inquiry, you can expect a response within 24 hours.
Required fields are marked *


Name *:
Email *:
Phone :
Message *:
ip:
riqi:
yemian:
yemian: Click image to refreshClick the picture to refresh
 
7 steps diamond polishing pad for granite marble stone polishing
7 steps diamond polishing
Buy best arix segment for diamond core drill bit from China professional factory
Buy best arix segment for
Vacuum brazed diamond wire saw rope for reinforced concrete and Steel
Vacuum brazed diamond wir
Granite marble stone diamond cutting wire saw
Granite marble stone diam

conatct us

Tel: +86-595-2288-5227(Ext:2)
Mob: 0086-133-2887-5227 WhatsApp/Wechat
Email: sales@diamond-blade.org

Copyright © 2006-2023.China(Quanzhou) Diamond Saw Blade Association All Rights Reserved. Email:sales@diamond-blade.org